Архив форумов ЦИТФорума

[Agp]

Здравствуйте.
Граждане кто настраивал Hylafax, помогите
Имеется сервер RedHat7.3 linux, который функционирует как dial-in сервер(mgetty+ppp) и как fax server c использованием этого самого пакета Hylafax. Все работает -- но поочереди. Читая доки по Hylafax я понял что идея такая пользоват ь из менеджер модемов faxgetty и если звонок не факс, а дата то из него вызывать mgetty. Так вот это и не получается. Он не хочет отличать звонок data, вызывать mgetty и продолжает пищать что хочет факс.
Лог сервера:
Mar 19 12:41:08 mgw-tv FaxGetty[10886]: MODEM ZYXEL Omni56K/1.01
Mar 19 12:41:08 mgw-tv FaxGetty[10886]: MODEM input buffering disabled
Mar 19 13:04:37 mgw-tv FaxGetty[10886]: MODEM input buffering enabled
Mar 19 13:05:16 mgw-tv FaxGetty[10886]: ANSWER: Ring detected without successful handshake
Mar 19 13:05:16 mgw-tv FaxGetty[10886]: MODEM set DTR OFF
Mar 19 13:05:16 mgw-tv FaxGetty[10886]: MODEM set DTR ON
Mar 19 13:05:18 mgw-tv FaxGetty[10886]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF
Mar 19 13:05:18 mgw-tv FaxGetty[10886]: MODEM flush i/o
Лог клиента:
Mar 19 13:04:37 sysadmin pppd[18651]: pppd 2.4.1 started by root, uid 0
Mar 19 13:04:38 sysadmin chat[18652]: abort on (ERROR)
Mar 19 13:04:38 sysadmin chat[18652]: abort on (BUSY)
Mar 19 13:04:38 sysadmin chat[18652]: abort on (NO ANSWER)
Mar 19 13:04:38 sysadmin chat[18652]: abort on (NO CARRIER)
Mar 19 13:04:38 sysadmin chat[18652]: timeout set to 5 seconds
Mar 19 13:04:38 sysadmin chat[18652]: send (AT^M)
Mar 19 13:04:38 sysadmin chat[18652]: send (ATZ^M)
Mar 19 13:04:38 sysadmin chat[18652]: expect (OK)
Mar 19 13:04:38 sysadmin chat[18652]: AT^M^M
Mar 19 13:04:38 sysadmin chat[18652]: OK
Mar 19 13:04:38 sysadmin chat[18652]: -- got it
Mar 19 13:04:38 sysadmin chat[18652]: send (ATS7=120^M)
Mar 19 13:04:38 sysadmin chat[18652]: expect (OK)
Mar 19 13:04:38 sysadmin chat[18652]: ^M
Mar 19 13:04:38 sysadmin chat[18652]: ATZ^M^M
Mar 19 13:04:38 sysadmin chat[18652]: OK
Mar 19 13:04:38 sysadmin chat[18652]: -- got it
Mar 19 13:04:38 sysadmin chat[18652]: send (ATDT07713289^M)
Mar 19 13:04:38 sysadmin chat[18652]: timeout set to 125 seconds
Mar 19 13:04:38 sysadmin chat[18652]: expect (CONNECT)
Mar 19 13:04:38 sysadmin chat[18652]: ^M
Mar 19 13:05:37 sysadmin chat[18652]: ATDT07713289^M^M
Mar 19 13:05:37 sysadmin chat[18652]: NO CARRIER
Mar 19 13:05:37 sysadmin chat[18652]: -- failed
Mar 19 13:05:37 sysadmin chat[18652]: Failed (NO CARRIER)
Mar 19 13:05:37 sysadmin pppd[18651]: Connect script failed
Конфиг модема в hylafax:
CountryCode: 7
AreaCode: 095
FAXNumber: "+7 095 1111111"
LongDistancePrefix: 0
InternationalPrefix: 10
DialStringRules: etc/dialrules
ServerTracing: 5
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: ...

[Agp]

конфиг модема в hylafax:
CountryCode: 7
AreaCode: 095
FAXNumber: "+7 095 1111111"
LongDistancePrefix: 0
InternationalPrefix: 10
DialStringRules: etc/dialrules
ServerTracing: 5
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-r -b -s %s %l"
LocalIdentifier: SviazBank
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
PercentGoodLines: 50
MaxConsecutiveBadLines: 50
MaxRecvPages: 25

ModemType: Class2.0 # use this to supply a hint

Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0
Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D (direct)
Class2CQCmd: "" # commands to enable copy quality proc.
Class2AbortCmd: AT+FKS # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
Class2TBCCmd: AT+FPP=1
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLI # set local identifier command
Class2DCCCmd: AT+FCC # set modem capabilities command
Class2DISCmd: AT+FIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FPI # set polling identifier command
Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command
Class2PIECmd: AT+FIE=0 # disable interrupt-enable command
Class2PTSCmd: AT+FPS # set post-page status command
Class2PTSQueryCmd: AT+FPS? # set post-page status query command
Class2SPLCmd: AT+FSP # set polling indicator command
Class2NFLOCmd: AT+FLO=0 # set no flow control command
Class2SFLOCmd: AT+FLO=1 # set software flow control command
Class2HFLOCmd: AT+FLO=2 # set hardware flow control command

конфиг mgetty
#
# mgetty configuration file
#
# this is a sample configuration file, see mgetty.info for details
#
# comment lines start with a "#", empty lines are ignored
# set the global debug level to "4" (default from policy.h)
debug 2
# access the modem(s) with 115200 bps
speed 115200
port-owner uucp
port-group uucp
port-mode 0664

# USR Sportster 33,6 external modem (ttyS0, 0x3f8, irq 4, 115200)
# modem-type `auto' working perfectly, but no need yet
port ttyS0
direct y
toggle-dtr n
modem-type auto
data-only y
force-init-chat "" \d\d\d+++\d\d\dATH0 OK A ...

[Agp]

конфиг mgetty:
#
# mgetty configuration file
#
# this is a sample configuration file, see mgetty.info for details
#
debug 2
speed 115200
port-owner uucp
port-group uucp
port-mode 0664

# USR Sportster 33,6 external modem (ttyS0, 0x3f8, irq 4, 115200)
# modem-type `auto' working perfectly, but no need yet
port ttyS0
direct y
toggle-dtr n
modem-type auto
data-only y
force-init-chat "" \d\d\d+++\d\d\dATH0 OK ATZ OK
init-chat "" ATZ OK AT&M0E1Q0S0=0 OK

faxgetty запускается через init
s0:2345:respawn:/usr/sbin/faxgetty ttyS0

[and3008]

-

[Agp]

/etc/mget../login.config:
----------------**************--- -------------
# login.config
#U* uucp @ /usr/lib/uucp/uucico -l -u @
#/FIDO/ uucp fido /usr/local/lib/fnet/ifcico @
#
/AutoPPP/ - @ /usr/sbin/pppd call dial-in
#
#* - @ /bin/login @
----------------**************----------------
/etc/ppp/ peers/dial-in:
----------------**************-------------- --
nodefaultroute
auth
refuse-chap
require-pap
disconne ct "/usr/sbin/chat -- \d+++\d\c OK ath0 OK"
debug 9
netmask 255.255.255.0
proxyarp
192.168.1.7:
ms-dns 192.168.1.2
----------------**************----------------